Monday, September 30, 2013

September Update


A few things have happened this month some for the layout other to support family and I spend a week or so off colour but overall a better month than earlier in the year.  My wife bought me a SP Poster which is proudly hanging in out home theatre room and I finally got around to putting up the railway crossing sign, that my wife bought for me about two decades ago, over the entrance to the train room.  I have started another Launchpad project, this time for a grade crossing. I have done some more on the U50 decoder and lighting install and I fitted some acrylic sheet to protect the passenger station at Hornertown.

SP Poster






Sign over Train Room Entrance

My wife bought this for me about two decades ago and it was supposed to be installed over the entrance to my shed containing layout number 3 at our previous residence.  We the comments from family members about "when is is going to happen can stop now!



My duck under sized so I will fit "underneath when I am in a wheel chair"......


Railway Crossing

For some time now I have been thinking about a road crossing and having operating crossing lights and a sound module.  Well using a Launchpad seemed to be the answer to tie all the components together into a working system.

The Givens:

  • Crossing Globes operate on 5-10V
  • Relays Operate on 12V
  • Block Watchers used for signal logic operate on 12V but not on a common ground with rest.
  • Double track crossing
  • IR detector at crossing to detect train without resistor axles (covers situation when locos of train have exited the power block leaving nothing to be detected by the Block Watcher)
  • Grade crossing should continue to operate for a minimum of 3 seconds after road crossing is cleared
  • Signal system power to be isolated from crossing system


The grade crossing to operate when:

  • A train enters either end of either double track section that the crossing is in
  • A non resistor axle piece of rolling stock which is either stationary or moving over the road crossing

Planning where the major components might go


Designing the power supplies


then building it



 relay configuration

sound module
 Wiring scheme



Major components mounted ready for testing.

Hornertown Passenger Station


I fitted some 6 mm acrylic sheet to protect the passenger station at Hornertown it is sandwiched between the fascia and some 9 mm MDF to provide strength (for when the grand kids try and climb up by hanging onto the acrylic sheet!  This method has worked well at Huntington.

U50 Modifications

Last month I started the biggest install challenge I have ever attempted.  I removed the factory boards and did a total rewire and fitted a Tsumami sound decoder and have been replacing the bulbs with LEDs - it has been my first go at 0602/0603 smt LEDs.  I learnt that 0.25 mm wire is too strong and when bending inside the loco the tension can destroy the smt LED.  I should have used the 0.010 wire from the outset.  Do NOT fix the smt's with ACC - use Krystal Klear so when it all goes wrong it can be undone easily...  I found some figures for crew.

Below are a few pics







That's it for this month.


Thanks to those that continue to help me achieve my ambitions and hello again to all my followers!


Till the end of October.



-ooOOOoo-

Thursday, September 5, 2013

August Update


This post is a bit late as I have been away for a few days with m wife to celebrate our 36th wedding anniversary.  The cellar has grow after our visits to just a few wineries in the beautiful Clare Valley.

Well work recommenced this month and a few things were done in Hornertown with trees, vegetation and passenger station getting attention.  There was also some improvements to lighting at Huntington and LeMaistre Loco and some work on scenery in Onka Valley.  Lastly I have been working on my Athearn U50 installing a Tsunami sound decoder.

Hornertown 

BJ & I had a few sessions to talk and plan then commence work on detailing around Hornertown Yard and Pasenger Station.  The photos tell the story.

Vegetation

BJ and I have started to add some tress and bushes to the basic ground cover.











Last of the Pedestrian barrier

It is built and undercoated and we discovered that the paint needed to match the rest of the barrier is safely locked away at Chris's house.




Passenger Terminal

A considerable amount of time has been spent cutting and trial fitting with consideration as to the final finished desired.  Again the photos show the process

Pavement trial fitting

Eastern end



Fitting the subway entrance




Scratch built steps into station building



Western end





Hand painted pavement







Wow what a difference in look - fabulous work BJ!



Waiting for the glue to dry


Palm trees added


Cutting out the perspex station building protection panel.

Lighting

There were a few spots on the layout where insufficient illumination was apparent. This month I replaced the six 20W halogen globes with 9W LED globes and added a further six down lights.  I also fitted three additional 35W halogen spotlights over LeMaistre Loco

Huntington 

With double the amount of lights now installed with only half of the original power consumption the results are great.




LeMaistre Loco

The shadows are now far more realistic and the "dull spots" have mostly gone leaving an acceptable outcome.





Onka Valley

BJ adding some more detail to the valley backdrop.





U50 Modifications

This will be the biggest install challenge I have attempted and I'm sure I will find some surprises along the way...  I have decided to remove the factory boards and do a total rewire and fit Tsumami sound decoder and replace the bulbs with LEDs - it will be m first go at 0602/0603 LEDs.

Decoder

Tsunami TSU-1000 Digital Sound Decoder Dual GE FDL-16 (U50)


Speakers

Tony's Dream Speakers 1.10 Diameter and enclosures which were sealed with Micro Krystal Klear when assembled.


Before Speaker Install

Speakers in place

Decoder fitted over motor

I fitted two pieces of .030 polystyrene strip using the manufacturers board mountings to ensure the wiring can be kept away from the moving parts.  The decoder is held in place with Kapton Tape.

Lights

The assembly detailed below will be fixed inside on the roof of the body.

I joined machine pins and header pins so diodes can be inserted between the forward (white) and reverse (yellow) feeds for the marker lights to operate irrespective of loco direction. A piece of PC Board is soldered to allow plenty of space to get the +ve common (blue) wires to be attached

Decoder wires soldered to machine pins

Marker lights

Soldering the armature wire to the 0602 LED was somewhat challenging.


Wired LED glued in place behind the marker light lense.

Routing the wire was not as easy as I thought

Mars Lights

The manufacturers lens were drilled out to allow 1.0 mm long lens LED's to be fitted.  I placed the LEDs in from outside the body to get the correct alignment then soldered them together before removing to trial fit from the inside.  I had to file the top edge of the top led to allow for the wires from the emergency light to pass above them.

During testing I discovered that these LEDs are 5 mA not the usual 20 mA when I destroyed the first one.... I have limited the current to 2.5 mA and they are still quite bright.




Emergency Light

I will use a Red LED 650nm 40deg Clear 0603 (1.6x0.8 mm) fitted inside the housing then held in place with Micro Krystal Klear.
I removed the jewel and the fitting is hollow and allows the passage of the magnet wire.  I had to file the inside of the housing to allow the red SMT LED to fit.

Thanks to BJ for his untiring efforts on scenery components.

My scenery guru BJ


Chris should be returning soon following the birth of a Grandson so my time will be split between working on his new layout and my own.

That's it for this month.


Thanks to those that continue to help me achieve my ambitions and hello again to all my followers!


Till the end of September.



-ooOOOoo-